A soft or spongy spot in the floor
For sound structural recovery, most manufactured homes are decked in particleboard, which swells and loses its bond once it stays wet.
Homes and commercial properties
Deport, TX
Our building recovery team removes water and dries lightweight floors, walls, insulation, and underbelly materials commonly affected in mobile homes.
Signs to look for
As materials are evaluated, if you notice any of these problems, call us before water has more time to spread into nearby materials.
For sound structural recovery, most manufactured homes are decked in particleboard, which swells and loses its bond once it stays wet.
From the building building assessment, panel walls are joined with battens over the seams instead of taped and painted like drywall.
For sound structural recovery, vinyl covered gypsum panel walls sit directly on the decking, so they wick water upward from the floor.
As materials are evaluated, the seam where two sections join is the most common water entry point on a multi section home.
Across the affected building area, older homes with low slope metal roofs pond water at seams, vents and the edges.
As materials are evaluated, the furnace and water heater usually share one interior closet sitting directly on the decking.
What happens
Our building recovery team adjusts the work to what got wet, how far the water traveled, and which materials can be saved.
From the building building assessment, we note the home's age, whether it is a single wide or a double wide, and what the deck and the walls are actually made of.
Across the affected building area, particleboard decking that has swelled or lost its bond does not come back, and drying it longer will not change that.
From the building building assessment, panel walls come apart at the battens and the bottom course, which lets us dry the wall cavity without wrecking the whole room.
Across the affected building area, portable extractors and compact submersible pumps come through a 30 inch doorway and up a set of steps.
As materials are evaluated, many manufactured homes run a 100 amp service, which limits how much drying equipment the home can actually carry.
For sound structural recovery, water that reaches an in floor supply duct sits there and gets blown through every room.
Talk with a restoration specialist
Describe the source, the impacted rooms, and when you first noticed the damage.
What to expect
For sound structural recovery, here is how we usually handle mobile home water damage near Deport, TX.
As materials are evaluated, tell us the approximate age, whether it is a single wide or double wide, and where the water is showing.
Your callFrom the building building assessment, close the fixture valve, or the main at the lot pedestal if it is above ground and safe to reach.
+5 minutesAcross the affected building area, keep people and heavy furniture off any soft area, because wet particleboard loses strength quickly.
+15 minutesAcross the affected building area, we confirm the deck material, the wall panel type, the marriage line if there is one, and where the ducts run.
On arrivalAcross the affected building area, water comes off hard flooring and out of carpet and padding, and contents get lifted and blocked.
First hours on siteAs materials are evaluated, we tell you which decking sections, wall panels and cabinets are coming out and which are staying.
Same dayAs materials are evaluated, equipment is placed and the amperage counted before anyone drives away, so your service is not overloaded overnight.
Before we leaveUnderstanding the cost
As materials are evaluated, we explain the recommended work and price before you approve the job. As materials are evaluated, these examples show what may change the estimate.
| Common situation | What the estimate may include | Typical range |
|---|---|---|
| One room of a manufactured home, clean water, extraction plus three to four days of drying | From the building assessment, national estimate. Across the affected building area, a supply line or fixture caught quickly, with little or no decking replacement. | $900 to $2,500 |
| Most of a single wide affected, clean water | From the building assessment, national estimate. Across the affected building area, includes extraction, padding removal, wall panel bottom course work and five to seven days of equipment. | $3,000 to $8,000 |
| Double wide with several rooms and decking replacement | From the building assessment, national estimate. As materials are evaluated, water across the marriage line, two duct runs and significant decking and panel replacement. | $6,000 to $18,000 |
| Particleboard decking replacement, per square foot | As materials are evaluated, national estimate for removing and replacing failed floor decking, before the finish flooring above it. | $3 to $10 |
| Wall panel replacement, per square foot | From the building assessment, national estimate for vinyl covered gypsum panel sections including batten work. As materials are evaluated, older patterns may not be matchable. | $2 to $6 |
| Manufactured home work priced by affected area, clean water | From the building assessment, national estimate. From the building assessment, handy once someone has measured the wet area and given you a number. | $3 to $7 per square foot |
| Belly wrap drained, wet insulation out, underbelly repair coordinated | National estimate. Priced and detailed on our under house water removal page, which owns that construction-aware scope. | $800 to $3,500 |
| After hours or overnight dispatch charge | From the building assessment, national estimate. As materials are evaluated, one charge on the first visit, for nights, weekends and holidays. | $100 to $400 |
What the deck is made of
Across the affected building area, particleboard decking that has swelled has to be replaced, and that is labor plus material plus flooring above it.
How much of the home is wet
From the building assessment, pricing follows affected square footage.
Single section or multi section
From the building assessment, a double wide is roughly twice the area and adds the marriage line as both a leak path and a drying boundary.
How clean the water was
From the building assessment, supply line water is the least damaging case and saves the most material.
Wall panel count
From the building assessment, panel replacement is priced by area and by how many batten lines have to be opened.
Duct involvement
For sound structural recovery, clearing and drying in floor ducts is straightforward.
Why timing matters
For sound structural recovery, water can keep moving into nearby materials even when the surface looks dry.
From the building building assessment, once the panel swells and its bond fails, it stays swollen and weak no matter how long you dry it.
For sound structural recovery, the vinyl film on these panels is effectively a vapor barrier on the room side, so moisture cannot escape toward the air you are drying.
As materials are evaluated, small air volume means moisture saturates every room within hours, so there is no comfortable dry side to retreat to.
From the building building assessment, standing water inside a supply duct or the crossover duct gets pushed through the home each time the system runs.
Helpful service information
From the building assessment, start with the short explanation. For sound structural recovery, open a card if you want a little more detail.
As materials are evaluated, floors are typically decked in particleboard over relatively shallow floor joists, glued and stapled as a system.
Across the affected building area, manufactured homes are built to the federal HUD Code, which produces a very different set of materials from a site built house.
For sound structural recovery, that film behaves like a vapor barrier on the room side, so moisture in the gypsum core cannot escape toward the dry air you are creating in the room.
As materials are evaluated, the vinyl face on a panel wall is the detail that catches inexperienced crews.
As materials are evaluated, a single section home holds a fraction of the air a two story house does, so evaporating water pushes relative humidity up very quickly and evaporation then stalls.
As materials are evaluated, air volume is the quiet variable in a home this size. As materials are evaluated, a single section home holds a fraction of the air a two story house does, so evaporating water pushes relative humidity up very quickly and evaporation then stalls.
Help near you
Choose your area below, or call (877) 361-7453 and describe what happened.
Common questions
For sound structural recovery, it depends entirely on the deck material. As materials are evaluated, most manufactured homes use particleboard decking, and once it has swelled or lost its bond it does not recover, so those sections come out.
Across the affected building area, as a national estimate, one wet room with a few days of drying commonly runs $900 to $2,500.
As materials are evaluated, three reasons. Across the affected building area, the decking is often particleboard rather than plywood, and the walls are vinyl faced gypsum panels joined with battens rather than taped drywall.
From the building building assessment, the bottom few inches are usually the problem, because panels sit on the deck and wick water upward.
As materials are evaluated, that is a separate construction-aware scope from the work inside your home, and our under house water removal page covers it in full.
From the building building assessment, extraction usually finishes in one to three hours. As materials are evaluated, drying then takes about three to five days for a typical loss, sometimes less because there is less material.
From the building building assessment, yes, and it is one of the most commonly missed steps. From the building building assessment, supply ducts run inside the floor and the crossover duct links the sections on a double wide, so water sits in them and gets blown through the home.
Talk with a restoration specialist
Describe the source, the impacted rooms, and when you first noticed the damage.
Areas we serve
Our building recovery team evaluate homes, businesses, and managed properties throughout Deport, TX and nearby communities.
View the area on Google Maps